1. Kinetico Water Softener Model 60 Manual

Kinetico water softeners first appeared on the scene in 1970 as the brainchild of two engineers in search of a non-electric means to automatically treat water. Manufactured for both commercial and residential households, Kinetico water softeners operate uninterrupted during the regeneration process and provide soft and safe water through the means of a turbine and gears instead of electricity. Troubleshoot your softener if you notice household soap no longer lathering well, a soapy or scummy buildup on your skin after showering, or if you notice a film on glasses and dishware after cleaning or running them through the dishwasher.

You are here:: Model 60 Page of 4 Water Soft WSCB-32D is Autotrol 255 4 60i or Fleck 5 600 SE Just to confirm. Our softener is WaterSoft model WSCB-32D.

I was told by CSI Control, who referred me to you, that the control valve is 255 46 WaterSoft G9,G10,G12, and G13 models can have a version of the Fleck 5 600 or Fleck 2510, but may also use the proprietary Isobar 2092 control Powerhead on the valve. So, please include photos when inq Kinetico systems are proprietary. Except for RESIN, High Capacity Standard Mesh can be used if the Hardness is less than 20 grains per gallon, or the resin amount per tank is 1 cu.ft.

Fine M Fleck Piston 24507 - Fleck Model 5656 / 5665 UF are NOT the same as Mechanical Versions of Fleck 5 600 or SE, SXT versions We have only seen this version of the Main Piston in models sold in Autotrol Model 3 60, 363 and Model 368 Parts This valve is not very common, but we can special order most parts for it. And some parts are also used in other Autotrol Valve Models, so a Search by Part Question: I have an Autotrol 7 60 water softener that is displaying an ERR 3.

My manual said the most common problem is the optical sensor, so I ordered one from you, but it failed to fix the problem. How To Repair A Logix Controller that Forgets the Time Of Day After Power Interruptions The Logix Controller is designed to retain the correct time of day for up to eight hour My softener does not remove the water from my salt tank when it regenerates. What should I check? Make sure all the fittings are tight.

Kinetico Water Softener Model 60 Manual

Also check the tubing going to the sa Resin Replacement ( When, Why, and How ) When or Why to replace your softening resins. First let me say that is has been my experience that the resins The number one reason for low water flow from a reverse osmosis system is low air pressure in the holding tank. The Problem: Low Volume and Poor Pressure Little to No air pressure will result in If you notice AIR in the water lines the morning after your softener has regenerated, AND the brine water level is normal ( meaning the valve has been sucking the water out and refilling properly ), t PROBLEM CAUSE CORRECTION 1. Softener fails to regenerate. Electrical service to u An obvious problem that can occur is for the timer motor to fail. The motors turn at 1 rpm, so it is quite easy to tell if it is turning. A more common problem is for one or more of the drive gears t Older Bruner softeners ( Model B-790-4 ) used an Autotrol model 1 60 valve in late 1970s and early 80s.

This model is like the 155 valve in size, but does not use an 'air check' on the valve. In this The General Ionics valve and tank are proprietary in design. Only a few of the parts made for 'Fleck' valves are interchangeable. Many key parts of the valve ( like main piston and seal kit ) are prop. Customer wrote in looking for replacement tank for HOW TO ( H2ow To ) softener: Andrew,The hole in the top is approx.2 3/4' across-the overall height is 18 3/4' tall - outer diameter is approx. 10' If you install a new Fleck 5 600 motor timer and it does keep the time o.k. And even kicks the unit into 'REGEN', but that's as far as it will go, THEN:.

It is possible you have dropped the cu The valve body of the Rainsoft Amazon Gold Series ( and not electronic Silver Series ) are basically the Fleck 5000 or newer Pro Flow version of the Model 5000 valve. See our parts list here: Salty water in the morning is a common problem. It occurs most commonly because the internal seals of the Valve leak highly salty water into the cold water lines during the regeneration cycle. Typ I am trying to locate a parts list & schematics for the Tectonic Water Softener Model #CB-32D.

I have called the following Tectonics and was referred to a company it had be sold to: CSI: Water.